Watts CEN2000 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 92 of 131

8.9 TROUBLESHOOTING

TABLE 8.9: WHM Troubleshooting

FAULT INDICATION

PROBABLE CAUSE

CORRECTIVE ACTION

Manager LEDs are
flashing on 2
Controllers

1.

Two Edge Controllers
have their WHM Mode
menu option set to WHM
Manager.

1.

Check the WHM Mode entries in the units
which have their displays flashing. Change one
of the WHM Mode settings to WHM Client.

MANAGER

LED on

one or more WHM
units is

Off

.

1.

Improperly connected or
faulty RS485 Modbus
wiring.

2.

Improper Comm address.

3.

Unit Comm address is not
unique.

1.

Check the polarity of the RS485 Comm
connections on the I/O board of the affected
unit. Also, ensure that all Modbus wiring
connections to the unit are secure.

2.

Verify that the address of the affected unit is
within the allowable range (1 thru 16).

3.

Check to ensure that none of the units have the
same Comm address.

Actuator-controlled
Sequencing Valve
does not open

1.

Control cable not
connected to valve
actuator.

2.

24 VDC power not being
supplied to valve
actuator.

3.

Defective valve actuator.

1.

Ensure that the control cable from the unit’s I/O

Box is connected to the valve actuator.

2.

Remove the enclosure cover from the valve
actuator and verify that 24 VDC is present at
Terminal 2 of the actuator.

3.

Replace valve actuator. Following replacement,
the actuator stroke will have to be calibrated to
ensure it fully opening and closing.

8.10 SEQUENCING VALVE DESCRIPTION & OPERATION

Installation of the Sequencing Isolation Valve (P/N

21008C

) is described in Section 2.13.

Figure 8-16: Actuator-Controlled Sequencing Valve (P/N 21008C)

The Actuator Housing contains a cover which is removed by simply loosening a single captive
screw. Removing the cover provides access to a PC Board containing wiring connections and
control circuitry components as shown.

The components on the PC board include DIP switches which are preset at the factory and
should not be changed unless instructed to do so.

ACTUATOR

3”

BRASS BALL

VALVE

«
...
90
91
92
93
94
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: Vanguard Страницы: 36

Бренд: WaterCare Страницы: 7

Бренд: Radiant Страницы: 24

Бренд: Annovi Reverberi Страницы: 18

COBRA DS 0600 E

Бренд: BUSCH Страницы: 24

mr. steam AromaSteam MS AROMA

Бренд: Feel Good Страницы: 20

Бренд: ICI Caldaie Страницы: 48

Бренд: DeLonghi Страницы: 4

Бренд: Warmtech Страницы: 21

Бренд: Edwards Страницы: 60

DHH 12 Si control

Бренд: STIEBEL ELTRON Страницы: 168

Toyotomi Laser 30

Бренд: Toyostove Страницы: 31

AQUAJET PFN 10000 PLUS

Бренд: Aquael Страницы: 54

Бренд: Serenity Страницы: 3

Бренд: Wayne Страницы: 4

Little Giant PES-70

Бренд: Franklin Electric Страницы: 2

Бренд: Xvent Страницы: 29

Бренд: W. Tombling Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды