Watts CEN2000 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 78 of 131

8.3.3 Temperature Sensor Calibration

The Temperature Sensors screens allows you calibrate the unit’s temperature sensors to
achieve optimal performance. Complete the following to calibrate the temperature sensors.

Figure 8-2: Temperature Sensors Screen

1. Go to:

Main Menu

→

Calibration

→

Input/Output

→

Temperature Sensors

.

2. Press the Sensor parameter and select the temperature sensor you want to calibrate. The

following sensors are available for calibration:

•

Feed Forward

•

Outside Temp

•

Lower Inlet

•

Exhaust

•

Air Inlet

•

Outlet

3.

The selected sensor’s current reading appears in the Current Reading field.

4. If there is an independent way to measure the temperature, and it differs from the Current

Reading, enter an appropriate value in the Offset parameter.

8.3.4 Manual Mode Password Required

To prevent unauthorized or inadvertently setting the unit, entering a valid password is required
to set the Edge in Manual Mode. Any level password will enable Manual Mode.

8.3.5 Auto-Manager Transfer

The Auto-Manager Transfer feature, once enabled, automatically transfers WHM Manager
functionality to a new unit if the current WHM Manager fails or loses power.

To use this feature (default = Disabled), go to:

Advanced Setup

→

WHM Cascade

→

Cascade Configuration

on the unite designated as the WHM Manager

and set

Auto-Manager

Transfer

to

Enabled

, then choose the address of the backup unit in the

Backup Manager

Addr

parameter. You can also specify a delay before transferring manager functionality in the

Auto-Manager Timer

parameter.

8.3.6 Run Hours and Run Cycles

Run hours and run cycles are monitored to select the Lead unit and Lag unit (next on unit) in a
WHM Cascade mode. Run hours and run cycles can be increased to match other units in an
existing plant to make sure that the unit is properly sequenced. Run hours and run cycles can
only be increased but cannot be decreased. Once entered, the changes made will be
permanent and this feature will not allow changing to the previous value.

Only PVI personnel are permitted to change this menu item. To increase the

Run Hours

or

Run

Cycles

, go to

Main Menu

→

Advanced Setup

→

Unit

→

Unit Settings

→

Run Hours

.

«
...
76
77
78
79
80
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: laguna Страницы: 24

Бренд: Navien Страницы: 108

Бренд: Vasco Страницы: 15

Бренд: Tapworks Страницы: 36

Pure Link 1300 Series

Бренд: lancer Страницы: 20

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Бренд: Wacker Neuson Страницы: 72

BASIC VASF 2.120/1-0.AC115

Бренд: Becker Страницы: 6

Бренд: Noritz Страницы: 26

Бренд: UNITED Страницы: 8

Бренд: DAXOM Страницы: 20

Бренд: OmarLift Страницы: 28

Бренд: Dimplex Страницы: 3

Speedflow SF10SS

Бренд: Hyco Страницы: 12

Бренд: A.O. Smith Страницы: 36

Бренд: Somogyi Elektronic Страницы: 23

Бренд: CEH Страницы: 4

VERSATYLE SG 1000

Бренд: EBARA Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды