Watts CEN2000 Скачать руководство пользователя страница 83

Страница: 83 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 83 of 131

Remaining WHM parameters are in

WHM Cascade

→

Operating Controls.

Operating Controls

→

Sequencing Control Parameters

Menu Item Display

Available Choices or Limits

Default

Minimum

Maximum

Next On Valve Pos

16%

100%

50%

The valve position that triggers the next unit to come on line.

Next Off Valve Pos

16%

100%

25%

The valve position that triggers the next unit to come off line.

WHM Max Units

WHM Manager only

–

The maximum number of units that will fire. For example: if there

are 5 units, but this setting is set to 3, the plant will not fire more than 3 units.

WHM Client Screen

WHM Manager Screen

Figure 8-7: Operating Controls: Sequencing Controls Screens

Operating Controls

→

Anti-Cycling Parameters

Menu Item Display

Available Choices or Limits

Default

Minimum

Maximum

On Delay

300

The minimum time a unit must stay off after shutting down or going into standby.

WHM Off Delay

300

30 sec.

The amount of time the low fire position will be delayed.

Shutoff Delay Temp

The temperature above setpoint the unit may rise to during delay shutdown.

Figure 8-8: Operating Controls: Anti-Cycling Control Screen

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды