Watts CEN2000 Скачать руководство пользователя страница 43

Страница: 43 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 5: INITIAL START-UP

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 43 of 131

5.2 TOOLS & INSTRUMENTS FOR COMBUSTION CALIBRATION

To properly perform combustion calibration, the proper instruments and tools must be used and
correctly attached to the unit. The following sections outline the necessary tools and
instrumentation as well as their installation.

5.2.1 Required Tools & Instrumentation

The following tools and instrumentation are necessary to perform combustion calibration:

•

Digital Combustion Analyzer: Oxygen accuracy to ± 0.2%; Carbon Monoxide (CO) and

Nitrogen Oxide (NOx) resolution to 1 PPM

•

0 to 16 inch W.C. (0 to 4.0 kPa) manometer or equivalent gauge and plastic tubing

•

1/4-inch NPT-to-barbed fittings for use with gas supply manometer

•

Small and large flat blade screwdrivers

•

Tube of silicone adhesive

5.2.2 Installing Gas Supply Manometer

16” W.C. (4.0 kPa) gas supply manometer (or gauge) is used in the following ways:

•

Mounted on the

upstream

side of the SSOV to verify that the gas supply pressure is

within the required range of 4” W.C. and 14” W.C.

•

Mounted on the

downstream

side of the SSOV to monitor the gas pressure during the

Combustion Calibration procedure, described in 5.3.

1. 1. Turn off the main gas supply upstream of the unit.

2. 2. Remove the top panel and/or front panel from the Water Heater to access the gas train.

3. 3.

Remove the 1/4” NPT plug from the leak detection ball valve on the upstream or

downstream side of the SSOV, as needed during testing, as shown in the Figure below.

4. 4. Install an NPT-to-barbed fitting into the tapped plug port.

5. 5. Attach one end of

the plastic tubing to the barbed fitting and the other end to the 16” W.C.

(4.0 kPa) manometer.

Figure 5-2: 1/4 Inch Gas Plug Location

LEAK DETECTION BALL

VALVE

LOW GAS PRESSURE
SWITCH

1/4” NPT PLUG

(Install manometer here
for

downstream

combustion calibration
reading)

NATURAL GAS INLET

SSOV

HIGH GAS
PRESSURE
SWITCH

1/4” NPT PLUG

(Install manometer here for

upstream

combustion

calibration reading)

TO AIR/FUEL VALVE

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды