Watts CEN2000 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 7: MAINTENANCE

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 73 of 131

7.10 RECOMMENDED PERIODIC TESTING

W A R N I N G !

Periodic testing of all Water Heater controls and safety devices is required to ensure they
continue to operate as designed. Precautions must be taken while tests are being performed
to protect against bodily injury and property damage. The owner or user of an automatic
Water Heater system should set up a formal system of periodic preventive maintenance and
testing. Tests should be conducted on a regular basis and the results recorded in a logbook.

Recommended Periodic Testing

ITEM

FREQUENCY ACTION BY REMARKS

Gauges, monitors and
indicators

Daily

Operator

Visual inspection and record readings in operator log

Instrument and
equipment settings

Daily

Operator

Visual check against factory recommended
specifications

Weekly

Operator

Verify factory settings

Firing Rate Control

Semi-
Annually

Service Tech Verify factory settings

Annually

Service Tech

Check with combustion calibration test equipment
(see Section 5.2) and the O

2

sensor (Section 7.4).

Flue, vent, stack and
intake air duct

Monthly

Operator

Visually inspection condition and check for
obstructions

Spark Igniter-Injector Weekly

Operator

See Section 7.2:

Ignitor-Injector

in this guide.

Air/Fuel Valve position Weekly

Operator

Check position indicator dial. See Section 4.2.

SSOV Leakage test

Annually

Service Tech

Check for leakage in accordance with the SSOV

manufacturer’s (Siemens) recommendations.

Flame failure

Weekly

Operator

Close manual gas shutoff valve and check safety
shutdown. See Section 6.7.

Flame signal strength Weekly

Operator

Check flame strength in

the Edge Controller’s

Unit

Status

screen.

Low water level cut off
and alarm

Weekly

Operator

See Section 6.4:

Low Water Level Fault Test.

Slow drain test

Semi-
Annually

Operator

Perform a slow drain test in accordance with ASME
Water Heater and Pressure Vessel Code, Section IV.

High water temp.
safety control test

Annually

Service Tech See Section 6.5:

Water Temperature Fault Test

.

Operating controls

Annually

Operator

See Section SECTION 3:

Edge Controller Operation

.

Low air flow

Monthly

Operator

See Section 6.8 and 7.8.

High and low gas
pressure interlocks

Monthly

Operator

See Sections 6.2 and 7.3.

Air/Fuel Valve purge
position switch

Annually

Service Tech See Section 6.10.

Air/Fuel Valve ignition
position switch

Annually

Service Tech See Section 6.11.

Safety valves

As required Operator

Check per A.S.M.E. Water Heater and Pressure Vessel
Code, Section IV.

Inspect burner
components

Semi-
Annually

Service Tech

See Section 7.6:

Burner Inspection

.

«
...
71
72
73
74
75
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: Daikin Страницы: 36

Бренд: iGenix Страницы: 6

Бренд: Raymarine Страницы: 24

SunCentric Series

Бренд: Dankoff Solar Страницы: 11

Бренд: A-Star Страницы: 29

Бренд: Zehnder Pumpen Страницы: 32

Бренд: Homa Страницы: 11

Бренд: Clarke Страницы: 12

Бренд: REMKO Страницы: 20

Taro HCS SJ Series

Бренд: Texmo Industries Страницы: 41

Бренд: Reality Leuchten Страницы: 86

Dura-Power Den & Del

Бренд: A.O. Smith Страницы: 2

Бренд: DèLonghi Страницы: 7

Бренд: Ducar Страницы: 30

Бренд: Calpeda Страницы: 19

Бренд: OmarLift Страницы: 28

Бренд: Geotech Страницы: 32

Бренд: Eaton Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды