Watts CEN2000 Скачать руководство пользователя страница 80

Страница: 80 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 80 of 131

The following messages may appear on this screen:

FAILSAFE ACTIVE

– The Client Failsafe Mode has been activated

All Heaters On

– All available heaters are ignited

All Heaters Off

– All available heaters are off

Enabling First

– The first heater is allowed to ignite and its valve is opened

Enabling Next

– The next heater is allowed to ignite and its valve is opened

Wtr Htr Inactive

– This Client unit is inactive; its valve is closed and can’t ignite

Wtr Heatr Active

– This Client unit is active; its valve is opened and it can ignite

REMOTE SIG FAULT

– Remote signal fault

WHMS FAILSAFE

– WHMS is in Failsafe Mode

8.6 WHM PARAMETERS

The WHM parameters are under

Advanced Setup

→

WHM Cascade

. Many of these are

preset at the factory and cannot be altered by the user.

NOTE:

Some parameters will not appear on screen if they are not enabled.

WHM Cascade

→

Cascade Configuration Parameters

Menu Item
Display

Available Choices or Limits

Default

Minimum

Maximum

WHM Unit
Mode

Off, WHM Client, WHM Manager

Off

Enables/disables the WHM mode and sets the unit to function as a WHM Client or WHM
Manager. Set the

WHM Unit Mode

option to

WHM Manager

for the unit designated as the WHM

Manager and to

WHM Client

for all other units on the network.

Auto-
Manager
Transfer

Enable, Disable

Disable

Enables (Password Level 2 required) an Automatic WHM Manager Switch-Over function. When
enabled, the WHM will automatically select a new Manager if the current Manager fails or loses
power. Used with Auto-Manager Timer option, described below.

Auto-
Manager
Timer

10 sec.

120 sec.

30 sec.

When

Auto-Manager Transfer

Enabled

, allows user to select the elapsed time interval between

failure of the WHM Manager and switch-over to a new WHM Manager.

Auto-
Manager
Addr

Read Only

The address of the WHM Manger.

Backup
Manager
Addr

The address of the WHM Backup Manger.

WHM Unit Mode = WHM Client

WHM Unit Mode = WHM Manager

Figure 8-4: Cascade Configuration Screens

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды