Watts CEN2000 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SAFETY PRECAUTIONS

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 11 of 131

Requirements for Massachusetts Installations

1. The equipment listed in Section 10 entitled "Equipment Not Required to Be Vented" in the
most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room
or structure separate from the dwelling, building or structure used in whole or in part for
residential purposes.

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM
PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas
equipment provides a venting system design or venting system components with the
equipment, the instructions provided by the manufacturer for installation of the equipment and
the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system
components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT
PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas
fueled equipment does not provide the parts for venting the flue gases, but identifies "special
venting systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance
or equipment installation instructions; and

2. The "special venting systems" shall be Product Approved by the Board, and the
instructions for that system shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented
gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all
venting design instructions shall remain with the appliance or equipment at the completion of
the installation.

……………….[End of Extracted Information From 248 CMR 5.08 (2)]…………………

«
...
9
10
11
12
13
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: Taurus Alpatec Страницы: 52

Бренд: Wayne Страницы: 8

Бренд: Wayne Страницы: 20

Бренд: Wayne Страницы: 8

Бренд: Wayne Страницы: 12

Бренд: Zoeller Страницы: 8

Бренд: Airetool Страницы: 20

Бренд: SMC Networks Страницы: 19

Бренд: Waterous Страницы: 10

Бренд: ARDES Страницы: 16

Blue Flame series

Бренд: HeatStar Страницы: 16

Бренд: Eldom Invest Страницы: 12

Бренд: Cadet Страницы: 8

Бренд: AQUASYSTEM Страницы: 12

Serve Better CP-RP

Бренд: Server Страницы: 8

Бренд: YAMADA Страницы: 25

Бренд: Tacmina Страницы: 80

Бренд: YAMADA Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды