Watts CEN2000 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 10: TROUBLESHOOTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 104 of 131

Centurion Troubleshooting Procedures

Fault

Probable Causes

Corrective Action

4.

Blocked blower inlet or inlet
ductwork.

4.

Inspect the inlet to the combustion blower including
any ductwork leading up to the combustion blower
for signs of blockage.

5.

No voltage to Blocked Inlet
switch from Edge Controller.

5.

During the start sequence, verify that 24 VAC is
present between each side of the switch and
ground. If 24 VAC is not present, refer fault to
qualified service personnel.

6.

PROBABLE CAUSES from 3 to
12 for AIRFLOW FAULT
DURING IGNITION apply for
this fault.

6.

See CORRECTIVE ACTIONS for AIRFLOW FAULT
DURING IGNITION, items 3 to 12.

7.

Missing or improperly
connected Blocked Flue
jumper.

7.

Check auxiliary box to be sure Blocked Flue input is
jumpered and properly connected.

AIRFLOW
FAULT
DURING
RUN

1.

Blower stopped running due
to thermal or current
overload.

1.

Check blower for signs of excessive heat or high
current draw that may trip thermal or current
overload devices.

2.

Blocked Blower inlet or inlet
ductwork.

2.

Inspect the inlet to the blower, including any
ductwork leading up to the combustion blower, for
signs of blockage.

3.

Blockage in air filter or
Blocked Inlet switch.

3.

Remove the air filter and Blocked Inlet switch and
inspect for signs of blockage, clean or replace as
necessary.

4.

Defective Blocked Inlet
switch.

4.

Verify that 24 VAC is present between each side of
the switch and ground. If 24 VAC is not present at
both sides, replace switch.

5.

Combustion oscillations.

5.

Run unit to full fire. If the unit rumbles or runs
rough, perform combustion calibration.

6.

Probable causes from 3 to
16 for AIRFLOW FAULT
DURING IGNITION applies
for this fault.

6.

See CORRECTIVE ACTIONS from 3 to 12 for AIRFLOW
FAULT DURING IGNITION.

DELAYED
INTERLOCK
OPEN

1.

Delayed Interlock Jumper
not properly installed or
missing.

1.

Check to insure jumper is properly installed across
the Delayed Interlock terminals in the I/O Box.

2.

Device proving switch
hooked to interlocks is not
closed.

2.

If there are 2 external wires on these terminals,
check if an end switch for a proving device (such as a
pump, louver, etc.) is tied to the interlocks. Ensure
the device and/or its end switch is functional. A
jumper may be temporarily installed to test the
interlock.

«
...
102
103
104
105
106
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: VEAB Heat Tech Страницы: 40

Бренд: Hamilton Beach Страницы: 18

Бренд: YANGTECH Страницы: 16

Бренд: Eaton Страницы: 29

Бренд: Calpeda Страницы: 43

Бренд: Gude Страницы: 64

Бренд: Stübbe Страницы: 32

Sanitizer Plus ASP1-1044

Бренд: Water Right Страницы: 30

Бренд: Immergas Страницы: 40

Бренд: Jandy Pro Series Страницы: 4

VERSAFILLER P EBF Series

Бренд: Oasis Страницы: 21

SBC 1100 ADV PLUS FR

Бренд: Quick Страницы: 76

Бренд: hajdu Страницы: 132

Бренд: Farelek Страницы: 14

RAC15HL ScreenZone

Бренд: Claudgen Страницы: 20

Бренд: DROPSA Страницы: 9

Бренд: Lasko Страницы: 6

Бренд: salmson Страницы: 195

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды