Watts CEN2000 Скачать руководство пользователя страница 29

Страница: 29 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 2: INSTALLATION

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 29 of 131

Connector Strip J4 Terminals

Pin # Name

Description

Return Loop 2

In a multiple application environment, connection to the 2

loop return

header temperature sensor.

Shield

Connection to the shield from any cable.

RTD Spare 1

Reserved. Spare temp sensor

Sensor Ground

Ground connection for RTD Spare 1

RTD Spare 2

Reserved. Spare temp sensor

Return Header

Connection to the Supply Header temperature sensor (2 wire sensor P/N

24410C

, or 4 wire sensor P/N

61058C

) for:

•

Solar/Waste Heat application

Typically, used on Manager and Backup Manager units.

Sensor Ground

Ground connection for Return Header Temp sensor

DHW Temp

Connect the DHW tank temperature or DHW Loop Supply Temperature
sensor

Shield

Connection to the shield from any cable.

CO/Analog In +

Reserved for future use

CO/Analog In -

Connector Strip J5 Terminals

Pin # Name

Description

Spare Analog In 3 +

Connection to one of the following signals:

•

SmartPlate Valve input

•

Swing V1 feedback

•

Swing V2 Feedback

•

VS Pump Feedback (Variable Speed Pump Feedback)

•

Remote Setpoint 2

•

DHW VSP Fdbk

To assign/program its function, go to the Controller’s

Main Menu

→

Advanced Setup

→

Ancillary Devices

→

Analog Inputs, then set the Analog

Input Source parameter to Spare Analog In 1, Spare Analog In 2, or Spare
Analog In 3.

Spare Analog In 3 -

Spare Analog In 1 +

Spare Analog In 1 -

Spare Analog In 2 +

Spare Analog In 2 -

Spare Analog Out 1 +

Connection to one of the following signals:

•

Fire Rate

•

Cascade Valve

To assign/program its function, go to the Controller’s

Main Menu

→

Advanced Setup

→

Ancillary Devices

→

Analog Outputs, then set the

Select Output parameter to Spare Analog Out 1.

Spare Analog Out 1 -

DHW V.S. Pump +

Recirc pump on the unit

DHW V.S. Pump -

Spare Analog Out 3 +

Connection to the Fire Rate signal.

To assign/program its function, go to the Controller’s

Main Menu

→

Advanced Setup

→

Ancillary Devices

→

Analog Outputs, then set the

Select Output parameter to Spare Analog Out 3.

Spare Analog Out 3 -

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды