Watts CEN2000 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 5: INITIAL START-UP

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 44 of 131

5.2.3 Accessing The Analyzer Probe Port

1. Remove the

1/4” NPT plug from the exhaust manifold.

2. If necessary, adjust the stop on the combustion analyzer probe so it will extend mid-way

into the flue gas flow.

DO NOT install the probe at this time.

Figure 5-3: Analyzer Probe Port Location

5.2.4 Recommendations For WHM Operation

It is strongly recommended that installations with multiple CENTURION units operate in Water
Heater Management (WHM) mode (see Section 3.13 for instructions on installing the actuator-
controlled Sequencing Isolation Valve). This is to ensure the system flow is divided between
units as demand increases, and that all units receive equal run time and additional Water
Heaters are activated based on the

Next On

Valve Pos

firing rate setting.

In case of pre-heated DHW systems with multiple

CENTURION units, it is recommended to

lower the

Next On

Valve Pos

setting to 30-40% (Default=50%), so subsequent Water Heaters

are engaged sooner to provide rapid response and divide the system flow over additional units.
In case of DHW pre-heat systems, the required temperature rise through an individual unit can
be much lower to ensure flow per unit does not exceed 50 gal. (189 L) per minute.

5.3 COMBUSTION CALIBRATION

CENTURION Water Heaters are set up for Natural Gas, as specified by the Style Number on
the Sales Order, and calibrated for Standard NOx emissions (<20 ppm) before shipping.

Recalibration as part of initial start-up is necessary due to changes in the local altitude, gas BTU
content, gas supply piping and supply regulators. Combustion Calibration Test Data sheets,
shipped with each unit, must be filled out and returned to PVI for proper Warranty Validation. It
is important to perform the combustion calibration procedure below to provide optimum
performance and keep readjustments to a minimum.

COLD WATER INLET

CONDENSATE DRAIN

DRAIN VALVE

BUILDING
RECIRCULATION
WATER INLET

ANALYZER

PROBE PORT

«
...
42
43
44
45
46
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: Waterous Страницы: 36

Бренд: Paragon Страницы: 16

Бренд: FanWorld Страницы: 11

Бренд: Quantum Страницы: 4

Бренд: Jata Страницы: 32

Бренд: Nachfolger Страницы: 2

Бренд: Quooker Страницы: 12

Бренд: Ulvac Страницы: 54

Бренд: Dancover Страницы: 7

RJS-75SS Series

Бренд: red lion Страницы: 32

Бренд: ICI Caldaie Страницы: 48

KOE000010_11_12

Бренд: Kasanova Страницы: 10

Бренд: Lynx Страницы: 22

Бренд: Versamatic Страницы: 18

Бренд: Purmo Страницы: 8

Dura-Power Den & Del

Бренд: A.O. Smith Страницы: 2

Бренд: SAER Elettropompe Страницы: 44

MiniTank WM-1.0

Бренд: Waiwela Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды