Watts CEN2000 Скачать руководство пользователя страница 55

Страница: 55 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 6: SAFETY DEVICE TESTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 55 of 131

6.2 LOW GAS PRESSURE TEST

To simulate a low gas pressure fault, refer to Figure 6-2 and perform the following steps:

1. Remove the front panel from the Water Heater to access the gas train components.

2. Make sure the 1/4" ball valve located at the inlet side of the SSOV is closed.

3. Remove the 1/4" NPT plug from the ball valve.

4. Install a

16” W.C. (0–4 kPa)

manometer or gauge where the 1/4" plug was removed.

5. Slowly open the 1/4" ball valve.

6. Go to Main Menu

→

Diagnostics

→

Manual Run enable the Manual Mode control

7. Adjust the Air/Fuel Valve position

between 25% and 30%

using the

and

–

controls.

8. While the unit is firing, slowly close the external manual gas shut-off valve upstream of

the unit (not shown).

9. The unit should shut down and display

Fault Lockout -

Gas Pressure

Fault

approximately the pressure shown below:

LOW Gas Pressure, ± 0.2” W.C. (± 50 Pa)

Model

Natural Gas

CEN2000 FM & DBB Single-Fuel

3.8” W.C. (946 Pa)

10. Close the 1/4" ball valve (opened in Step 5).

11. Fully open the external manual gas shut-off valve (not shown) and press

CLEAR

button.

12. The fault message should clear,

FAULT

indicator go off, and the unit should restart.

13. Upon test completion, close the ball valve, remove the manometer and replace the 1/4"

NPT plug removed in step 3.

Figure 6-2: LOW Gas Pressure Test Components

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды