Watts CEN2000 Скачать руководство пользователя страница 70

Страница: 70 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 7: MAINTENANCE

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 70 of 131

7.7 CONDENSATE DRAIN TRAP

All CENTURION Water Heaters contain a condensate trap (P/N

24441C

), located external to

the unit, attached to the

exhaust manifold’s drain at the rear of the unit.

This trap must be

inspected

for leaks and blockages,

cleaned

to ensure that the float is free to

move, and condensate flows normally, and the O-Ring (P/N

84017C

included in all 24 Month

Maintenance Kits) replaced if it is worn or damaged. In addition, you must ensure the vent
(under the removable cover) is free and clear of obstructions.

Figure 7-5: External Condensate Trap, Cross-Section & Exploded View

If your system includes a condensate neutralizer, the active ingredient must be periodically
replaced.

Figure 7-6: Condensate Trap and Neutralizer

CONDENSATE TRAP

CONDENSATE
NEUTRALIZER

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды