Watts CEN2000 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 10: TROUBLESHOOTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 102 of 131

SECTION 10:

TROUBLESHOOTING

10.1 INTRODUCTION

This section is intended to aid service/maintenance personnel in isolating the cause of a fault in
your CENTURION Water Heater. The troubleshooting procedures below are presented in
tabular form on the following pages. These tables are comprised of three columns labeled:
Fault Indication, Probable Cause and Corrective Action. The numbered items in the Probable
Cause and Corrective Action columns correspond to each other. For example, Probable Cause
No. 1 corresponds to Corrective Action No. 1, etc.

NOTE:

All O

2

Trim troubleshooting messages are included in Section 9.5, above.

When a fault occurs in the unit, proceed as follows to isolate and correct the fault:

10.1.1 Fault Correction

1. Observe the fault messages displayed on the Edge Controller.

2. Refer to the Fault Indication column in the table below, and locate the Fault that best

describes the existing conditions.

3. Proceed to the Probable Cause column and start with the first item for the Fault Indication.

4. Perform checks and procedures listed in the Corrective Action column for the first Probable

Cause candidate.

5. Continue checking each additional Probable Cause for the existing fault until the fault is

corrected.

6. Section 10.2 contains additional troubleshooting information that may apply to situations in

which no fault message is displayed.

If the fault cannot be corrected using the information provided in the Troubleshooting Tables,
contact your local PVI Representative.

«
...
100
101
102
103
104
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: Makita Страницы: 24

Бренд: Navien Страницы: 48

Бренд: Navien Страницы: 2

Бренд: HearthRite Страницы: 24

Бренд: Sure Flame Страницы: 32

Бренд: Kamoer Страницы: 2

Бренд: First Sales Страницы: 26

Бренд: salmson Страницы: 16

Бренд: Binks Страницы: 22

Бренд: Solar Energy Страницы: 4

Бренд: Olimpia splendid Страницы: 12

Бренд: DELEX Страницы: 7

Milton Roy Milroyal Series

Бренд: Accudyne Industries Страницы: 68

Бренд: Wacker Neuson Страницы: 60

Бренд: Dimplex Страницы: 28

Бренд: Pentair Страницы: 12

Бренд: Thermor Страницы: 40

Бренд: Qlima Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды