Watts CEN2000 Скачать руководство пользователя страница 49

Страница: 49 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 5: INITIAL START-UP

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 49 of 131

Note the following points:

•

Both switches display the temperature to which the switch is set (the temperature

limit),

not

the actual temperature it is reading.

•

Both switches can display temperatures in Fahrenheit or Celsius.

•

The

Auto-Reset

switch is preset to 160ºF (71°C) but can be adjusted as needed to

suit local conditions, as described below.

Figure 5-8: Over-Temperature Limit Switches

5.4.1 Adjusting The Automatic Reset Limit Switch Temperature

1. Power unit ON and remove the front panel to expose the Over-Temperature Limit switches.

Press the Automatic Reset Limit Switch’s SET button: SP appears in the display.

3. Press the SET button again. The current setting stored in memory is displayed.

Press the ▲ or ▼ arrow buttons to change the display to the desired temperature setting.

5. When the desired temperature is displayed, press the SET button.

6. Press both the SET and

▼ arrow buttons at the same time. This stores the setting in memory;

note that OUT1 appears in the upper-left corner of the display as confirmation.

Figure 5-9: Auto-Reset Over-Temperature Limit Switch

5.4.2 Resetting The Manual Reset Limit Switch

Perform the following steps to rest the Manual Reset Limit Switch after it has gone into Alarm
mode, and after the temperature has fallen at least 10 degrees below the limit.

1. Power unit

and remove front panel to expose Over-Temperature Limit switches.

Press the Manual Reset Limit Switch’s

RST

(Reset) button.

3. You can now restart the unit.

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды