Watts CEN2000 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 85 of 131

Figure 8-10: Operating Controls: Lead/Lag Control Screen

8.7 WHM HARDWARE INSTALLATION & SET-UP INSTRUCTIONS

The following sections provide the basic installation and set-up instructions for implementing a
Water Heater Management System (WHM) to control up to 16 CENTURION Water Heaters.

8.7.1 Installation Notes

Multi-unit configurations require a sequencing valve. Building automation system is available on-
board via Modbus TCP, BACnet MSTP and BACnet IP (go to

Main Menu

→

Advanced Setup

→

Comm & Network

→

BAS

).

If using ProtoNode SSD then you

must

adhere to the procedure below. Failure to complete

these steps can result in the failure of the WHM system.

a) Do

NOT

install the ProtoNode Device at the outset of the installation. If already installed,

you must physically disconnect it from the Modbus network in I/O board.

b) Make sure that the Modbus load and bias resistors are properly configured for the system

to operate without the ProtoNode installed.

c) Temporarily set the WHM system for Constant Setpoint mode of operation (see below).

d) Turn on and completely test the installation to verify that it is operating proper.

e) Once the installation is working properly as a WHM system, install the ProtoNode Device.

f) Make sure that the Modbus load and bias resistors are properly configured for the system

to operate with the ProtoNode installed.

g) Set the WHM system for desired mode of operation (Setpoint mode).

h) Test the system completely with the ProtoNode installed.

8.7.2 Hardware Installation

All CENTURION Water Heaters that will be controlled by a WHM Manager must be equipped
with an actuator-controlled Sequencing Isolation Valve. If this valve is not already installed at
the outlet, complete the instructions in Section 2.13.

8.7.3 WHM Modbus Network Wiring

As previously mentioned, all units being controlled by the WHM will be connected to a RS485
Modbus Network. All Modbus networks are wired in a daisy-chain configuration using a
Manager/Client scenario as shown below.

«
...
83
84
85
86
87
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: Haier Страницы: 2

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

Бренд: JABSCO Страницы: 4

Бренд: ACESOL Страницы: 36

Бренд: Calpeda Страницы: 27

Бренд: Watts Страницы: 12

Бренд: Gardena Страницы: 17

Бренд: Gardena Страницы: 12

RJS-75SS Series

Бренд: red lion Страницы: 32

Бренд: Edwards Страницы: 46

Бренд: Mesa Living Страницы: 18

home FKF2000CLCD

Бренд: Somogyi Страницы: 20

Бренд: Consort Страницы: 4

Бренд: Mepu Страницы: 28

Бренд: Scarlett Страницы: 14

Бренд: NARVI Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды