Watts CEN2000 Скачать руководство пользователя страница 39

Страница: 39 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 4: START SEQUENCE

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 39 of 131

Figure 4-3: Blocked Inlet and Blower Proof Switch

6. On the Ignition Sequence screen, the

Purging

indicator turns grey while purging is

underway and

Purge Timer

displays the purge cycle’s elapsed time in seconds.

Figure 4-4: Ignition Sequence Screen

–

Purging

7. Upon completion of the purge cycle, the Edge Controller initiates an ignition cycle and

the following events occur:

a) The Air/Fuel Valve rotates to the ignition position and closes the ignition switch. The

Dial on the Air/Fuel Valve (Figure 4-5) will read between

and

to indicate that

the valve is in the low fire position.

b) The Spark Cleaning cycle begins (default duration = 7 sec.) and the Ignition

Sequence screen’s

Spark Cleaning

indicator turns grey. This cycle turns on the

ignition transformer to produce a spark (with no gas flowing) to remove moisture and
carbon buildup from the spark element. For the duration of this cycle, the Controller
displays the

Cleaning Igniter

status message.

c) Following the Spark Cleaning cycle, power is applied to the gas Safety Shut-off

Valve (SSOV). When the SSOV indicates the Gas Valve is OPEN (POC), the
Ignition Sequence screen’s

Ignition

indicator turns grey.

BLOCKED INLET

SWITCH

BLOWER PROOF

SWITCH

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды