Watts CEN2000 Скачать руководство пользователя страница 56

Страница: 56 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 6: SAFETY DEVICE TESTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 56 of 131

6.3 HIGH GAS PRESSURE TEST

To simulate a high gas pressure fault, refer to Figure 6-4 and perform the following steps:

1. Close the 1/4" ball valve located at the High Gas Pressure switch.

2. Remove 1/4" NPT plug from the ball valve (Figure 6-4).

3. Install a

16” W.C. (0–4 kPa)

manometer or gauge where the 1/4" plug was removed.

4. Slowly open the leak detection ball valve.

5. Go to

Main Menu

→

Diagnostics

→

Manual Run

and enable

Manual Mode

control.

6. Set the valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

7. With unit running, monitor gas pressure on the manometer. Record pressure reading.

8. Slowly increase the gas pressure using the adjustment screw on the SSOV

while

counting the number of turns you make

9. The

FAULT

indicator should start flashing and the unit should shut down and display a

Fault Lockout -

Gas Pressure

Fault

message at approximately the value shown in

Table 6.3 (the High Gas Pressure switch setting). If the unit does not trip off within 0.2”
W.C. of the pressure shown, the switch needs to be replaced.

HIGH Gas Pressure, ± 0.2” W.C. (± 50 Pa)

Model

Natural Gas

CEN2000 FM & DBB Single-Fuel

2.4” W.C. (0.6 KPa)

10. Reduce the gas pressure by returning the SSOV adjustment screw to its original position

(the value recorded in step 8). This pressure should be within the range used during
combustion calibration, shown in the table above.

11. Unscrew and remove the plastic cover on the High Gas Pressure Switch and press the

red reset button. Replace cover.

12. Press the

CLEAR

button on the Edge Controller to clear the fault.

13. The fault message should clear, the

FAULT

indicator should go off and the unit should

restart (if in

Manual

mode).

14. Upon test completion, close the ball valve and remove the manometer. Replace the 1/4"

NPT plug removed in step 2.

Figure 6-3: High Gas Pressure Switch

Содержание CEN2000




































































































































Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды

Watts CEN2000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CEN2000

Отзывы:

Похожие инструкции для CEN2000

Бренды по названию

Популярные бренды