Watts CEN2000 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 79 of 131

8.3.7 High Temperature Governor

The High Temperature Governor is a feature that aggressively prevents the outlet temperature
from exceeding the “Temperature High Limit”. The High Temperature Governor is independent
of the system PID and Feed-Forward control methodology and independently modulates the
Valve Position (Fire Rate) if the outlet temperature dangerously approaches the

Temperature

Hi

Limit

parameter.

This feature has 5 separate temperature bands for more precise control.

This feature is enabled by the

TEMP GOV

parameter in

Main Menu

→

Advanced Setup

→

Performance

→

Temperature Control

→

FFWD Settings

. Once enabled, the 5 “governor”

items,

GOV Limit-5

to

GOV Limit-15

are available. When the Outlet Temperature nears the

value of the

Temperature Hi

Limit

parameter (

Advanced Setup

→

Performance

→

Temperature Control

→

Temperature Conformance

) the effective Fire Rate will be reduced

by the value entered in

GOV Limit-5

through

GOV Limit-15

.

8.4 WHM STATUS DISPLAYS

The following WHM status information will be displayed to inform the user of critical WHM real-
time operating conditions:

Once a unit is defined as the WHM Manager, the green Manager light appears on the
Controller’s face and the following information appears on the WHM Cascade Status screen:

MANAGER-DISABLED

– The Manager has been disabled and is not available

MANAGER-STANDBY

– The Manager is “Cycled Off” and is available to be lit off

MANAGER-IGNITED

– The Manager is ignited

On unit’s defined as WHM Clients, the flowing status information will be displayed on the Unit
Status screen:

CLIENT-DISABLED

– The Client has been disabled and is not available

CLIENT-STANDBY

– The Client is “Cycled Off” and is available to be lit off

CLIENT-IGNITED

– The Client is ignited

8.5 WATER HEATER MANAGEMENT ALTERNATING STATUS DISPLAYS

On both WHM Manager units, the following status information will alternate, and be displayed
on the WHM Cascade Status screen

:

Figure 8-3: WHM Cascade Status Screen

Status & Fault
Messages

«
...
77
78
79
80
81
...
»

Содержание CEN2000




































































































































Отзывы:

Нет отзывов

Похожие инструкции для CEN2000

Бренд: TapFlo Страницы: 35

Бренд: Rainman Страницы: 17

Бренд: Valor Fires Страницы: 17

Бренд: Walchem Страницы: 34

Бренд: WAGNER Страницы: 84

Бренд: WAGNER Страницы: 52

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Бренд: Energie Страницы: 31

HYDRA-SPRAY President A Series

Бренд: Graco Страницы: 20

Superflow Series

Бренд: Excalibur Water Systems Страницы: 39

Бренд: Dura Heat Страницы: 22

VERSAFILLER P EBF Series

Бренд: Oasis Страницы: 21

Infrared Heating

Бренд: Jigsaw Страницы: 11

Бренд: U.S. Products Страницы: 8

2JT Cartridge EV9608-10

Бренд: Everpure Страницы: 2

Бренд: Zibro Страницы: 14

Бренд: Paramount Fitness Страницы: 14

Бренд: A.O. Smith Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды