Trane IntelliPak 2 Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 195 / 220

RT-SVX24Q-EN 195
Table 73. Air-cooled condenser—refrigerant coil fin data (continued)
Tons
Coil Type
Coil Fin
Config.
Tube Dia. Coil Rows
Fins per foot
Coil Face Area
(sq. ft.)
Tube Type
120
Evaporator
Internally
Finned
1/2 3 168 106.25 Internally Finned
Hi-Cap Evap
Internally
Finned
1/2 6 168 106.25
Internally Finned
Condenser Enhanced 18 mm 2 276 161 Microchannel
130
Evaporator
Internally
Finned
1/2
4 168 106.25
Internally Finned
Hi-Cap Evap
Internally
Finned
1/2
6 168 106.25
Internally Finned
Condenser Enhanced 18 mm 2 276 161 Microchannel
150
Evaporator
Internally
Finned
1/2
6 168 106.25
Internally Finned
Condenser Smooth 18 mm 2 276 161 Microchannel
Fan Belt Adjustment
The supply fan belts and optional exhaust fan belts
must be inspected periodically to assure proper unit
operation.
Replacement is necessary if the belts appear frayed or
worn. Units with dual belts require a matched set of
belts to ensure equal belt length. When removing or
installing new belts, do not stretch them over the
sheaves; instead, loosen the adjustable motor-
mounting base.
Once the new belts are installed, adjust the belt tension
using a Browning or Gates tension gauge (or
equivalent) illustrated in
Figure 145, p. 195 .
Figure 145. Typical belt tension gauge
Deflection = Belt Span (in.)
64
Deflection = Belt Span (mm)
152
Force Scale
Span Scale
Large
O-Ring
Small
O-Ring
Belt Span
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e w w//C Ca ap pa acciitto orrss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err a an nd d d diisscch ha arrg ge e
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss a an nd d d diisscch ha arrg ge e a allll m mo otto orr sstta arrtt//rru un n
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an nn no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. F Fo orr v va arriia ab blle e
ffrre eq qu ue en nccy y d drriiv ve ess o orr o otth he err e en ne errg gy y sstto orriin ng g
cco om mp po on ne en nttss p prro ov viid de ed d b by y T Trra an ne e o orr o otth he errss,, rre effe err tto o
tth he e a ap pp prro op prriia atte e m ma an nu uffa accttu urre err’’ss lliitte erra attu urre e ffo orr
a allllo ow wa ab blle e w wa aiittiin ng g p pe erriio od dss ffo orr d diisscch ha arrg ge e o off
cca ap pa acciitto orrss.. V Ve erriiffy y w wiitth h a a C CA AT T IIIIII o orr IIV V v vo ollttm me ette err
rra atte ed d p pe err N NF FP PA A 7 70 0E E tth ha att a allll cca ap pa acciitto orrss h ha av ve e
d diisscch ha arrg ge ed d..
F Fo orr a ad dd diittiio on na all iin nffo orrm ma attiio on n rre eg ga arrd diin ng g tth he e ssa affe e
d diisscch ha arrg ge e o off cca ap pa acciitto orrss,, sse ee e P PR RO OD D--S SV VB B0 06 6* *--E EN N..
1. To determine the appropriate belt deflection:
a. Measure the center-to-center distance, in
inches, between the fan sheave and the motor
sheave.
b. Divide the distance measured in Step 1a by 64;
the resulting value represents the amount of
belt deflection for the proper belt tension.
2. Set the large O-ring on the belt tension gauge at the
deflection value determined in Step 1b.
3. Set the small O-ring at zero on the force scale of the
gauge.
4. Place the large end of the gauge on the belt at the
center of the belt span. Depress the gauge plunger
until the large O-ring is even with the of the second
belt or even with a straightedge placed across the
sheaves.
S Se errv viicce e a an nd d M Ma aiin ntte en na an ncce e