Trane IntelliPak 2 Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 166 / 220

166 RT-SVX24Q-EN
N No otte e:: The drive belt is a urethane stretch belt
designed to provide constant tension
throughout the life of the belt. No periodic
adjustment is required. Inspect the belt
annually for proper tracking and tension. A
properly tensioned belt will turn the wheel
immediately, with no visible slippage, when
power is applied.
4. If the wheel has difficulty starting, turn off the
power and inspect the wheel for excessive
interference between the wheel surface and the
four diameter seals. To correct interference, loosen
the diameter seal adjusting screws and back the
diameter seals away from the surface of the wheel.
Apply power to confirm free wheel rotation. Re-
adjust and tighten the seals according to
instructions in the “Service and Repair” section.
Damper Actuators
Stroke the actuators to observe full open and full
closure of the dampers.
Routine Maintenance
N NO OT TIIC CE E
E En ne errg gy y W Wh he ee ell D Da am ma ag ge e!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d rre essu ulltt iin n
w wh he ee ell d da am ma ag ge e..
D Do o n no ott u usse e a acciid d b ba asse ed d cclle ea an ne errss,, a arro om ma attiicc sso ollv ve en nttss,,
sstte ea am m,, o orr tte em mp pe erra attu urre ess iin n e ex xcce essss o off 1 17 70 0°°F F tto o cclle ea an n
tth he e w wh he ee ell..
D Do o n no ott u usse e a a p prre essssu urre e w wa assh he err tto o cclle ea an n e en ne errg gy y
w wh he ee ell sse eg gm me en nttss..
Cleaning the Energy Wheel
Disconnect all electrical power, then use a vacuum or
brush to remove accumulated material from the face of
the wheel. Examine the energy wheel monthly for
material build-up on the wheel. If more aggressive
cleaning is needed, removed the wheel segments and
follow these steps:
1. Wash the segments or the wheel in a five-percent
solution of non-acid-base coil cleaner (part no.
CHM00021 at your local Trane parts center) or in an
alkaline detergent and warm water.
2. Soak the segments in the solution until grease, oil,
and tar deposits are loosened.
3. Before removing the cleaner, rapidly run your
fingers across the surface of segments to separate
polymer strips for better cleaning action.
4. Rinse the dirty solution from the segments and
remove the excess water before re-installing the
segments in the wheel.
N No otte e:: Some permanent staining of the desiccant
may remain but is not harmful to
performance.
Cleaning Frequency
In reasonably clean office or school buildings, cleaning
with a coil cleaner solution may not be required for
several years. If the energy wheel is exposed to air
streams containing, for example, high levels of
occupant tobacco smoke, cooking facility exhaust air,
or oil-based aerosols found in machine shop areas,
annual or more frequent cleaning may be required to
remove these contaminants and restore performance.
Periodic inspection of the wheel should be done to
determine the cleaning intervals.
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
W WA AR RN NIIN NG G
R Ro otta attiin ng g C Co om mp po on ne en nttss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n rro otta attiin ng g cco om mp po on ne en nttss ccu uttttiin ng g a an nd d sslla assh hiin ng g
tte ecch hn niicciia an n w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss
iin njju urry y..
D Du urriin ng g iin nsstta alllla attiio on n,, tte essttiin ng g,, sse errv viicciin ng g a an nd d
ttrro ou ub blle essh ho oo ottiin ng g o off tth hiiss p prro od du ucctt iitt m ma ay y b be e
n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e a an nd d e ex xp po osse ed d rro otta attiin ng g
cco om mp po on ne en nttss.. H Ha av ve e a a q qu ua alliiffiie ed d o orr lliicce en nsse ed d sse errv viicce e
iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n p prro op pe errlly y ttrra aiin ne ed d iin n
h ha an nd dlliin ng g e ex xp po osse ed d rro otta attiin ng g cco om mp po on ne en nttss,, p pe errffo orrm m
tth he esse e tta asskkss..
High-maintenance applications may benefit from
keeping a spare set of clean segments on hand. This
allows for rapid change-out of clean segments with
minimal downtime. The dirty segments can then be
cleaned at a convenient time.
Segment Removal
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
IIm mp po orrtta an ntt:: Do not open the service access doors while
the unit is operating.
U Un niitt S Stta arrttu up p