Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 134 / 148

Maintenance

Replacing the Tungsten Lamp

124

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific



To replace the tungsten lamp

1. Turn off and unplug the instrument from the wall outlet or power strip.

2. Make sure the lamp has cooled (for at least 10 minutes).

3. Loosen the captive screw on the lamp door by rotating it counterclockwise about ¼ turn.

4. Raise the lamp door.

5. Unscrew the thumbscrew while holding the lamp assembly in place.

6. Carefully pull the assembly out until you can reach the connector.

7. Release the tab and disconnect the cable.

8. Unpack the new lamp assembly.

9. Use a soft, lint-free cloth to wipe off any fingerprints on the lamp.

10. Connect the cable to the connector.

WARNING

Turn off and unplug the instrument before removing the cover of the lamp

compartment.

Captive screw on lamp door

Thumbscrew

Lamp assembly

Tab on cable connector

Aligning the lamp assembly

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды