Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 53 / 148

Water Analysis Application

Using the One Point Adjustment Calibration Feature

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

3. Prepare a blank, reagent blank (reverse color methods only) and calibration standard with

a known concentration within the method range and near the expected sample
concentration.

Refer to the specific reagent chemistry section for detailed instructions.

4. Press the

Calculate 1pt Adjust

function key.

The screen below will appear with the Standard Concentration: value highlighted.

5. Press

enter

to edit this field, then use the numeric keypad to enter the concentration of

the standard and press

enter

6. Wipe the exterior of the blank vial and place the blank vial into the holder in the sample

chamber.

7. Close the sample chamber door.

8. Press the

Measure Blank

function key.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды