Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 20 / 148

Setting Up the Instrument

Setting Utility Parameters

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific



To set the date

1. Highlight

Set Date

and press

Enter

2. Press

Set Date

, type the date and press

Enter

3. Press

Set Month

, highlight the correct month and press

Enter

4. Press

Set Year

, type the year and then

Enter

5. Press

Esc

to save the settings.



To select the time format

You can set the instrument to display the time in either am/pm or 24-hour format. To change
the format, highlight

Time Format

and press

Enter

until the desired format (AM/PM or 24

hour) appears.



To set the time

1. Highlight

Set Time

and press

Enter

2. To set the hour, press

Set Hour

, type in the hour and press

Enter

3. To set the minutes, press

Set Minute

, type in the minute and press

Enter

4. To select between AM and PM (if in AM/PM time format), press

Set AM/PM

until the

appropriate setting appears.

Standby Mode

To prolong lamp life, your spectrophotometer has been pre-set at the factory to automatically
go into standby mode after 15 minutes of inactivity.

Since the tungsten lamp of the Orion AquaMate Vis spectrophotometer requires a 30-minute
warm-up, the spectrophotometer has been pre-set at the factory to Standby Mode OFF.



To change Standby Mode time

1. Highlight

Standby

and press

Enter

Note

Your changes are saved automatically (even during power down) by battery

backup.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды