Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 119 / 148

Performance Verification

Wavelength Accuracy - Internal

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

109

Wavelength Accuracy - Internal

This test locates the peaks of the internal xenon lamp (UV-Vis instruments) or internal
didymium filter (Vis instruments) and displays the expected and measured wavelengths for
the peaks.

• UV-Vis: A xenon lamp has strong, fundamental lines at 229 nm, 529 nm and 883 nm.

These lines are an essential property of xenon and serve as a fundamental standard.

• Vis: Didymium glass has strong transmission peaks at 585nm and 807nm. These peaks

are well characterized and suitable for use as wavelength standards.

When running the internal standard test, remember that:

• The wavelengths and tolerance values are preset and cannot be changed.

• The cell holder should be empty.



To run the Wavelength Accuracy - Internal test

1. Highlight

Wavelength Accuracy - Internal

and press

Enter

2. Press

Start Test

The results indicate pass or fail for each wavelength.

If the test fails, follow these guidelines:

• Repeat the test twice to verify that the test is failing consistently.

• Contact technical support for more troubleshooting advice.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды