Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 94 / 148

Absorbance Difference

Recalling a Test

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Recalling a Test



To recall a test

1. In the Absorbance Ratio screen (see

“Using the Absorbance Ratio Screen”

page 84

press

Stored Tests

2. Highlight the test to recall and press

Enter

Using the Absorbance Ratio Screen

Use this screen for:

•

Setting Up Test Parameters

•

Cell Correction

•

Saving a Test

• Viewing the list of stored tests

•

Measuring a Blank

•

Measuring Samples

Setting Up Test Parameters



To set up test parameters

1. In the Absorbance Ratio screen, highlight the parameter to set.

2. When the parameters are set, press

Save Test

to save the test or

Run Test

to measure a

blank or samples.

Note

If Cell Correction is ON, you must run the Setup Correction application before

you can access Run Test or Measure Samples.

Note

If Auto Save Data is ON, you must enter a Data File Name before you can

access Run Test or Measure Samples.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды