Главная
/
Thermo Scientific
/
Orion AquaMate 7000 Vis
/
Руководство пользователя

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Поделиться

Страница: 132 / 148

background image

23

Maintenance

Changing the Fuse

122

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Micro flowcells can be kept clean by:

• Flushing well with a solvent after use.

• Aspirating dilute acid, base, non-filming detergent or Clorox® through the cell in short

bursts.

• Storing with distilled water in the cell.

Cleaning the Windows of the Sample Compartment

Do not use acetone or abrasive materials to clean the windows of the sample compartment.
Instead, use a non-abrasive laboratory cleaning solution (such as a commercial cell cleaning
solution), distilled water or alcohol.

Use the liquid and a soft, lint-free cloth to clean the windows. Do not apply too much
pressure or the surface of the windows may be damaged. Be sure to remove all fingerprints.

Changing the Fuse

The fuse is located in the power entry module located at the center of the back panel of the
instrument.

• 120 VAC, 2.5 A, Slo Blo

• 240 VAC, 1.25 A, Slo Blo (2 required)



To change the fuse

1. Turn off and unplug the instrument from the wall outlet or power strip.

2. Position the instrument so you can access the power entry module on the back of the

instrument.

3. Remove the power cord.

4. Insert a flat-blade screwdriver into the notch on the fuse cover and pry off the cover.

IMPORTANT

Do not dry cells in an oven.

IMPORTANT

The instrument fuse must be replaced with the same type and rate.

IMPORTANT

If the fuse fails repeatedly, it may indicate a serious problem with the

instrument. Contact technical support as soon as possible.

«
...
130
131
132
133
134
...
»

Содержание Orion AquaMate 7000 Vis





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion AquaMate 7000 Vis

Бренд: Accu-Chek Страницы: 12

Бренд: Facom Страницы: 42

Бренд: Magnum Energy Страницы: 3

Kotron 805 series

Бренд: Magnetrol Страницы: 36

Бренд: Magnescale Страницы: 104

Бренд: Magnescale Страницы: 44

Бренд: EUPRY Страницы: 6

Бренд: REED Страницы: 4

Бренд: PASCO Страницы: 2

Analite NEP-5000

Бренд: Observator Instruments Страницы: 103

Бренд: Chauvin Arnoux Страницы: 44

Бренд: Droplet Страницы: 35

Бренд: Sencore Страницы: 75

Бренд: truflo Страницы: 33

Бренд: Hameg Страницы: 40

sound SMART RLT Sport

Бренд: VCA Страницы: 36

Бренд: Vega Страницы: 20

Бренд: Milkotester Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды