Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 73 / 148

Concentration Measurements—Advanced A-%T-C

Entering a Factor

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

4. Insert the blank and standard.

5. Press

Enter

to measure the blank and samples and display the absorbance and calculated

factor.



To measure a standard manually (using Manual 6 or Single Cell Holder)

1. Press

Run Standard

2. Enter the concentration of the standard and press

Enter

3. Insert the blank and standard.

4. Press

Measure Blank

If a 6-Position Cell Holder is installed, it moves to the B position to measure the blank
and returns to its previous position.

5. Press

Measure Standard

The instrument measures the absorbance of the standard and displays the absorbance and
calculated factor.

Entering a Factor



To enter a factor

Highlight

Factor

. To change the factor, enter the correct factor.

To change the units, highlight

Units

and select the correct units.

Measuring Samples



To measure a sample automatically (using Auto 6 or Auto 3)

1. Press

Run Test

2. When prompted, place the blank and samples in their cell positions and press

Enter

The instrument measures the blank and samples and displays the sample measurements.

3. Press

Measure Sample

to measure additional samples.



To measure samples manually (using Manual 6 or Single Cell Holder)

1. Press

Run Test

2. Insert the blank and sample.

A 6-Position Cell Holder can hold five samples.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды