Tennant 8210D Скачать руководство пользователя страница 29

Страница: 29 / 110

OPERATION

8210D 330210 (1--98)

EDGE SCRUB SWITCH

The edge scrub switch extends the scrub head to

the right to allow close edge scrubbing.

Out: Press the edge scrub switch during

scrubbing. The indicator light next to the switch

will illuminate.

In: Press the edge scrub switch. The indicator

light next to the switch will go out.

SQUEEGEE SWITCH

The squeegee switch controls the position of the

rear squeegee. The rear squeegee can be

operated separately from the scrub brushes for

the purpose of picking-up excess water without

scrubbing.

Lower: Press the squeegee switch. The indicator

light next to the switch will illuminate.

Raise and stop: Press the squeegee switch. The

indicator light above the switch goes off. There will

be a slight delay before the vacuum shuts off.

NOTE: The rear squeegee lowers and scrubbing

vacuum starts automatically when the scrubbing

operations start.

NOTE: The rear squeegee will raise and the

scrubbing vacuum will shut off after a short delay

when the machine travels in reverse.

NOTE: The rear squeegee will raise and the

scrubbing vacuum fan will shut off after a short

delay when the scrubbing operations are shut off.

351660

351661

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды