Tennant 8210D Скачать руководство пользователя страница 58

Страница: 58 / 110

OPERATION

8210D 330210 (6--03)

POST-OPERATION CHECKLIST

Check the engine oil level.

Check the engine coolant level.

Check the radiator and hydraulic cooler fins

for debris.

Check the hydraulic fluid level

Check the air filter indicator.

Check the skirts and seals for damage and

wear.

Check the condition of the sweeping and

scrubbing brushes. Remove any string,

banding, plastic wrap, or other debris

wrapped around them.

Check the sweeping brush patterns for

adjustment.

Check the condition of the hopper dust filter

and seals. Clean as required.

Check the tank cover seals for damage and

wear.

Clean the vacuum fan inlet filter.

Check the squeegees for damage, wear and

for deflection adjustment.

Check the vacuum hose for debris or

blockage.

ES machines; check the detergent tank

level.

Drain and clean the recovery tank.

ES machines; drain and clean the solution

tank and ES filter. Rinse level sensors.

Check the brakes and steering for proper

operation.

Check the fuel level

Empty the debris hopper.

Check the service records to determine

maintenance requirements.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды