Tennant 8210D Скачать руководство пользователя страница 15

Страница: 15 / 110

OPERATION

8210D 330210 (1--98)

BRAKE PEDAL

The brake pedal stops the machine.

Stop: Take your foot off the directional pedal and

let it return to the neutral position. Step on the

brake pedal.

PARKING BRAKE PEDAL

The parking brake pedal sets and releases the

front wheel brakes.

Set: While pressing the brake pedal as far as it

will go, set the parking brake by pressing the

parking brake pedal with the toe portion of your

foot.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

Release: Press on the brake pedal to unlock the

parking brake pedal.

IGNITION SWITCH

The ignition switch starts and stops the engine

with a key.

FOR SAFETY: When starting machine,

keep foot on brake and directional pedal

in neutral.

Preheat the glow plugs: Turn the key all the way

counter-clockwise and hold it there until the glow

plug light goes out.

Start: Turn the key all the way clockwise.

Release the key as soon as the engine starts.

Stop: Turn the key counter-clockwise.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды