Tennant 8210D Скачать руководство пользователя страница 90

Страница: 90 / 110

MAINTENANCE

8210D 330210 (6--04)

LEVELING THE REAR SQUEEGEE
Leveling of the squeegee assures even contact

the length of the squeegee blade with the surface

being scrubbed. Make sure this adjustment is

done on an smooth, level floor.

1. Lower the rear squeegee. Shut off the

engine and set the machine parking brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

2. Grab the rear squeegee assembly and lift it

until the assembly is resting on the

squeegee blades without any deflection.

3. Loosen the cam locking screws located on

the outside of each upper squeegee linkage

by turning 1/2 to 1 turn. Do NOT overturn as

this may disengage the cam locking tabs.

4. Adjust the squeegee blade until it deflects

more at the center and less at the tips. The

adjustment cams are located on the inside

of the squeegee frame. Turn the adjustment

cams forward to raise the tips of the

squeegee and backward to lower the tips of

the squeegee. The notch on the cam will be

straight up or slightly toward the rear when

adjusted properly. Hold the cam in this

position and tighten the cam locking screws.

5. Start the machine, lower the squeegee and

drive it forward to check the squeegee blade

deflection. The squeegee blade should

deflect more at the center and less at the

tips. See

ADJUSTING REAR SQUEEGEE

BLADE DEFLECTION

section of this

manual.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды