Tennant 8210D Скачать руководство пользователя страница 68

Страница: 68 / 110

MAINTENANCE

8210D 330210 (9--99)

LUBRICATION

ENGINE

Check the engine oil level daily. Change the

engine oil and oil filter every 50 hours of machine

operation. Use engine oil with a diesel rating

above

CD grade.

Fill the engine with oil to the level indicated on the

oil dipstick. Low oil level is indicated by the mark

closest to the end of the dipstick. Full level is

indicated by the mark closest to the top of the

dipstick. The engine oil capacity is 6.15 L

(6.5 qt) without the oil filter.

The engine oil drain hose is located on the

left--hand side of the machine, in front and above

the scrub brushes.

The engine oil filter is mounted on the front of the

engine, behind the hopper.

REAR WHEEL SUPPORT

The rear wheel support pivots the rear wheel. The

support has two grease fittings for the bearings.

The rear wheel support bearings must be

lubricated every 200 hours of operation. Use

Lubriplate EMB grease (Tennant part number

01433--1).

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды