Tennant 8210D Скачать руководство пользователя страница 20

Страница: 20 / 110

OPERATION

8210D 330210 (1--98)

HOPPER LEVER

The hopper lever raises and lowers the hopper.

Hopper up: Turn off all scrubbing and sweeping

functions. Pull and hold the hopper lever

backward until the hopper reaches the desired

height.

Hold: Release the hopper lever into the middle

position.

WARNING: Raised hopper may fall.

Engage hopper support bar.

Hopper down: Push the hopper lever forward until

the hopper has lowered completely.

NOTE: The main sweeping brush, side brush,

and sweep vacuum fan will stop operating when

the hopper is raised. If the sweep vacuum fan,

side brush switch, or the main brush switch is

pressed while the hopper is raised, none of the

sweeping operations will activate and the raised

hopper icon will appear on the control panel.

MAIN SWEEP BRUSH DOWN PRESSURE

KNOB

The main brush down pressure knob changes the

amount of contact the main brush has with the

surface being swept.

Increase: Turn the main brush down pressure

knob counter--clockwise.

Decrease: Turn the main brush down pressure

knob clockwise.

351651

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды