Tennant 8210D Скачать руководство пользователя страница 21

Страница: 21 / 110

OPERATION

8210D 330210 (6--04)

SIDE BRUSH DOWN PRESSURE HANDLE

The side brush down pressure handle changes

the amount of contact the side brush has with the

surface being swept.

Increase: Turn the side brush down pressure

handle counter-clockwise.

Decrease: Turn the side brush down pressure

handle clockwise.

CONTROL PANEL

The sweeping and scrubbing functions are

activated by the control panel. Features of the

control panel include six multi--function buttons

and graphics icons which display the current state

of the sweeping and scrubbing functions. The

control panel also features a display clock for

operator convenience, and a maintenance mode

that prompts the operator when to perform routine

machine maintenance.

By pressing the TENNANT logo, the operator can

cycle the control panel display through the

different function screens. Each function screen

allows the operator to enable or disable different

sweeping or scrubbing functions.

12 : 16 PM

0021

351652

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды