Tennant 8210D Скачать руководство пользователя страница 99

Страница: 99 / 110

MAINTENANCE

8210D 330210 (12--00)

TRANSPORTING THE MACHINE

1. Position the rear of the machine at the

loading edge of the truck or trailer.

FOR SAFETY: Use truck or trailer that

will support the weight of the machine.

NOTE: Empty the hopper, recovery tank, and

solution tank before transporting the machine.

2. If the loading surface is not horizontal or is

higher than 380 mm (15 in) from the ground,

use a winch to load machine.

If the loading surface is horizontal AND is

380 mm (15 in) or less from the ground, the

machine may be driven onto the truck or

trailer.

3. To winch the machine onto the truck or

trailer, attach the winching chains to the rear

tie down locations. The rear tie-down

locations are the bottom lips at each corner

of the rear bumper.

4. Turn the bypass valve 90

from the normal

position before winching the machine onto

the truck or trailer. See

PUSHING OR

TOWING THE MACHINE

section of this

manual. Make sure the machine is centered.

FOR SAFETY: When loading machine

onto truck or trailer, use winch. Do not

drive the machine onto the truck or

trailer unless the loading surface is

horizontal AND is 380 mm (15 in) or less

from the ground.

5. Position the machine onto the truck or trailer

as far as possible. If the machine starts to

veer off the centerline of the truck or trailer,

stop and turn the steering wheel to center

the machine.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды