Tennant 8210D Скачать руководство пользователя страница 83

Страница: 83 / 110

MAINTENANCE

8210D 330210 (1--98)

CHECKING AND ADJUSTING MAIN SWEEP

BRUSH PATTERN

1. Apply chalk, or some other material that will

not easily blow away to a smooth and level

section of the floor.

NOTE: If chalk or other material is not available,

in Step 4 allow the sweep brush to spin on the

floor for two minutes. A polish mark will remain on

the floor.

2. Position the main sweep brush over the

chalked area.

3. Start the main sweep brush.

4. Allow the main brush to sweep for 15 to 20

seconds while keeping a foot on the brakes

to keep the machine from moving.

NOTE: If chalk or other material is not available,

allow the sweep brush to spin on the floor for two

minutes. A polish mark will remain on the floor.

5. Stop the main sweep brush.

6. Drive the machine off the test area.

7. Observe the width of the brush pattern. The

proper brush pattern width is 50 to 65 mm

(2.0 to 3.0 in).

00582

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды