Tennant 8210D Скачать руководство пользователя страница 92

Страница: 92 / 110

MAINTENANCE

8210D 330210 (12--00)

SIDE SQUEEGEES

ADJUSTING THE SIDE SQUEEGEES
The side squeegee has one adjustment; height.

To change the height adjustment, disconnect the

squeegee spring from the clevis pin and move the

clevis pin to a different hole location.

SQUEEGEE BLADES

REAR SQUEEGEE

The rear squeegee has two squeegee blades.

Each blade has four wiping edges. To use them

all, start with one wiping edge. To use the next

wiping edge, rotate the blade end-for-end. To use

the next wiping edge, rotate the top edges down,

bottom edges up. To use the last edge, rotate the

blade end-for-end.

Replace any worn or damaged squeegee blades.

REPLACING OR ROTATING REAR SQUEEGEE

BLADES

1. Make sure the squeegee is raised off the

floor.

2. Shut the engine off and set the parking

brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

3. Open the retaining band clamp and remove

the squeegee blade.

4. Replace or rotate the squeegee blade to

allow a new edge to face the front of the

machine.

5. Place the squeegee blade over the

protrusions of the squeegee frame.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды