Tennant 8210D Скачать руководство пользователя страница 46

Страница: 46 / 110

OPERATION

8210D 330210 (1--98)

EMPTYING THE HOPPER

1. Stop sweeping.

NOTE: The filter shaker will operate automatically

and the hopper door will close automatically when

sweeping functions are deactivated.

2. Slowly drive the machine to the debris site

or debris container.

3. Pull and hold the hopper lever backward to

raise the hopper

FOR SAFETY: When using machine,

make sure adequate clearance is

available before raising hopper.

NOTE: Be aware that the minimum ceiling height

needed to high dump the hopper is 2286 mm

(90 in).

FOR SAFETY: When using machine,

move machine with care when hopper is

raised.

4. Drive the machine up to the debris

container.

5. Push the hopper door switch to open the

hopper door. The indicator light next to the

switch will illuminate and the hopper door

icon will indicate the hopper door is open.

6. Allow all of the debris in the hopper to fall

into the debris container.

351659

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды