Tennant 8210D Скачать руководство пользователя страница 22

Страница: 22 / 110

OPERATION

8210D 330210 (1--98)

SETTING THE DISPLAY CLOCK

1. Turn the machine off.

2. Press and hold the TENNANT logo button

while turning the ignition key to the ON

position. DO NOT start the engine. The ON

position is between the STOP and START

positions. Continue to press the TENNANT

logo button until the RESET PRESSURE

screen appears on the display. Release the

logo button.

3. Press and release the TENNANT logo

button. The ADJUST TIME screen will

appear on the screen.

4. Press the switch next to ADJUST TIME.

5. Set the time, date, and choose between the

12 or 24 hour clock modes by moving the

underline through the display by pressing

the switches next to the direction arrows.

Increase the value of the underlined

segment by pressing the switch next to the

positive (+) icon. Decrease the value of the

underlined segment by pressing the switch

next to the negative (--) icon.

6. Exit the ADJUST TIME function by pressing

the TENNANT logo switch.

7. Turn the key to the off position.

12 : 16 PM

0021

351653

Input Display

Adjust Time

Edge Scrub

351654

01 / 01 / 97

12 : 00 AM

351655

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды