Tennant 8210D Скачать руководство пользователя страница 2

Страница: 2 / 110

This manual is furnished with each new model. It provides

necessary operation and maintenance instructions.

Read this manual completely and understand the ma-

chine before operating or servicing it.

This machine will provide excellent service. However, the

best results will be obtained at minimum costs if:

The machine is operated with reasonable care.

The machine is maintained regularly - per the ma-

chine maintenance instructions provided.

The machine is maintained with manufacturer sup-

plied or equivalent parts.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials,

old machine components such as

batteries, hazardous fluids such as

antifreeze and oil, in a safe

environmentally way according to your

local waste disposal regulations.
Always remember to recycle.

MACHINE DATA

Please fill out at time of installation for future reference.

Model No.-

8210D

Serial No.-

Machine Options --

Sales Rep. --

Sales Rep. phone no. --

Customer Number --

Installation Date --

Tennant Company

PO Box 1452

Minneapolis, MN 55440

Phone: (800) 553--8033 or (763) 523--2850

CALIFORNIA PROPOSITION 65 WARNING:

Engine exhaust from this product contains chemicals known to the State of California to cause cancer,
birth defects, or other reproductive harm.

MAXPRO and ES are United States registered trademarks of the Tennant Company

Thermo Sentry is a United States trademark of Tennant Company.

Specifications and parts are subject to change without notice.

1998--2000, 2002--2006 TENNANT, Printed in U.S.A.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды