Tennant 8210D Скачать руководство пользователя страница 43

Страница: 43 / 110

OPERATION

8210D 330210 (1--98)

Polyester 8-double row main sweep brush

Polyester combines the durability of nylon with the

moisture resistance of polypropylene.

Polyester 24-row main sweep brush

Polyester combines the durability of nylon with the

moisture resistance of polypropylene. This high

density brush is recommended for applications

that sweep heavy accumulations of fine dust,

sand, or other similar material.

Polypropylene side brush

-- A good general

purpose brush for sweeping of light to medium

debris in both indoor and outdoor applications.

This brush is recommended when bristles may

get wet.

Nylon side brush

-- A longer life, general

purpose brush that is recommended for rough

surfaces.

Flat wire side brush

-- Recommended for

outside and curb-side sweeping where soilage is

heavy or compacted. The stiff wire bristles dig out

soilage. This brush is also recommended for

foundry sweeping when heat may melt synthetic

bristles.

Non-scuff polypropylene scrub brush

-- This

brush uses a softer, general --purpose poly bristle

to lift lightly compacted soilage, without scuffing

high-gloss coated floors.

Nylon scrub brush

-- Recommended for

scrubbing coated floors. Cleans without scuffing.

Super abrasive bristle scrub brush

-- Nylon

fiber impregnated with abrasive grit to remove

stains and soilage. Strong action on any surface,

performs well on debris build--up, grease, or tire

marks.

Black high- productivity stripping pads

-- Use

these 12 mm (0.50 in) pads for aggressive

stripping of floor finishes or sealers, or

heavy--duty scrubbing.

Brown stripping pads

-- Use these pads for light

stripping of floor finishes or sealers.

Blue scrubbing pads

-- Use these pads for

medium to heavy--duty scrubbing on industrial

floor surfaces.

Red buffing pads

-- Use these pads for

light--duty scrubbing on industrial floor surfaces.

White polishing pads

-- Use these pads for

surface cleaning of highly--polished or burnished

floors.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды