Tennant 8210D Скачать руководство пользователя страница 26

Страница: 26 / 110

OPERATION

8210D 330210 (1--98)

OPERATING LIGHTS SWITCH

The operating lights switch powers the headlights

and taillights on and off.

On: Press the top of the operating lights switch.

Off: Press the bottom of the operating lights

switch.

OPERATING/HAZARD LIGHT SWITCH

(OPTION)

The operating/hazard light switch powers the

headlights and taillights, and the revolving hazard

light (option) on and off.

Operating lights on: Press the top of the hazard

light switch.

Operating lights/Hazard light (option) on: Press

the bottom of the hazard light switch.

All lights off: Set the the hazard light switch in the

middle position.

SOLUTION FLOW SWITCH

The solution flow switch controls the amount of

solution that flows to the floor while scrubbing.

(1) Low: Press the top of the switch. Use this flow

rate for smooth floors and light dirt.

(0) Off: Press the middle of the switch.

(2) High: Press the bottom of the switch. Use this

flow rate for rough floors and heavy or compacted

dirt.

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды