Tennant 8210D Скачать руководство пользователя страница 27

Страница: 27 / 110

OPERATION

8210D 330210 (6--04)

MANUAL FLOW VALVE

The machine is equipped with a manually

adjustable solution flow valve that is located on

the right side of the scrubhead. The valve can be

adjusted to dispense either more or less solution.

Contact your TENNANT representative with

solution flow rate questions.

Maximum flow: Turn the flow lever to the

horizontal position.

Minimum flow: Turn the flow lever to the vertical

position.

SWEEP VACUUM FAN SWITCH

The sweep vacuum fan switch starts and stops

the sweep vacuum fan. Do not operate the

vacuum fan when sweeping in wet conditions.

Start: Press the switch. The indicator next to the

switch will illuminate.

Stop: Press the switch. The indicator light next to

the switch will go out.

NOTE: The sweep vacuum fan activates

automatically when the main sweeping brush

starts operating. The sweep vacuum fan will not

activate unless the main sweeping brush is

operating.

NOTE: The sweep vacuum fan will not start if the

hopper is raised, even slightly. If the sweep

vacuum fan switch is pressed while the hopper is

raised, the sweep vacuum will not start and the

raised hopper icon will appear on the control

panel.

351648

Содержание 8210D















































































































Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды

Tennant 8210D, Руководство оператора

Результаты поиска

Содержание 8210D

Отзывы:

Похожие инструкции для 8210D

Бренды по названию

Популярные бренды