Struck Magnatrac RS1000 Скачать руководство пользователя

Страница: 27 / 117

BM27

4132

Handle

“arm”

1172

Lynch

2255

Hand

Grip

4132

Handle

1703

Handle

4131

Link

2253

Spring

STEP 7.

With #4132 Handle ro-

tated fully forward, insert “opened”

#1172 Lynch Pin into aligned 3/8” hole

in #413 Handle “arm” and #4131 Link...

close Lynch Pin... see Photo at right.

NOTE:

#1172 Lynch Pin is used as a

“safety device” to keep your Rear Hitch

from falling during travel. When not

needed, close Lynch Pin and slip it

down length of #4132 Handle to store.

STEP 8.

Using liquid soap, lightly

“lubricate” the inside of your #2255

Hand Grip and slip it over forward end

of #4132 Handle... slide it down as far

as it will go.

CAUTION:

Be Aware that the

#2253 Springs can force the

#4132 Handle forward

rapidly

and

forcefully

if you don’t have

the #4132 Handle under

full hand con-

trol

when it’s not “locked” with #1172

Lynch Pin.

STEP 9.

Remove the two (2) #AI

Bolts installed in STEP 4 above.

Locate the two 5/8” holes in

#2259 Drawbar with mating 5/8” holes

in rear of #1693 Bail “channel”. Secure

with two (2) #AI Bolts removed above...

tighten.

NOTE:

For safety, you must have your

#1172 Lynch Pin in place per instruc-

tions in ”CAUTION” notice above.

2259

Drawbar

1693 Bail

“channel”

1172

Lynch

AI Bolts

Содержание Magnatrac RS1000






















































































































Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды

Struck Magnatrac RS1000, Инструкции по сборке приспособления

Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды