Struck Magnatrac RS1000 Скачать руководство пользователя страница 102

Страница: 102 / 117

BM102

STEP 2.

Per Photo above and at right, insert

an #AY Bolt into a #VV Washer and then into

(2) #1701 Tubes... make two (2) “assemblies”

like this.

STEP 3.

Align 3/4” hole in Left and Right Ears

of #1713 Bucket Hitch with mating 1/2” hole in

Left and Right Walls of #1712 Bucket Assem-

bly. From

outside,

insert a Bolt, Washer and (2)

Tubes “assembly” [made in STEP 2 above] into

each set of 1/2” & 3/4” Holes aligned above.

Secure each inside Bucket with VV Washer

and II Nut... tighten. See Photo at right.

STEP 4.

Per Photo at right, insert an AZ Bolt

into a #1690 Washer, #1741 Tube and second

#1690 Washer... make two (2) of these “as-

semblies”.

STEP 5.

Insert threads of each of these “as-

semblies” into center of their respective 3/8”

wide, “

curved serrated slots”

in Left & Right

Walls of #1712 Bucket Assembly. Secure each

bolt assembly inside Bucket with#1690

Washer and #KK Nut... tighten both Nuts. See

Photo of “Left Wall” at right... “Right Wall

should appear identical.

NOTE:

The

location

of the Bolt, Washer, Tube

Assemblies on their “curved slot” will determine

the Bucket’s angle relative to the ground... lo-

cated “further ahead” lowers the Bucket’s

“edge” for more aggressive digging.

AY Bolt

AZ Bolt

1690

1741

KK Nut

1690

VV Washer

(2) 1701 Tubes

II Nut

“curved serrated slot”

“curved

serrated

slot”

1690

AZ Bolt

“Left Wall”

1712

Bucket

Assembly

Bucket’s

“edge”

Содержание Magnatrac RS1000






















































































































Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Бренды по названию

Популярные бренды

Struck Magnatrac RS1000, Инструкции по сборке приспособления

Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Бренды по названию

Популярные бренды