Struck Magnatrac RS1000 Скачать руководство пользователя страница 71

Страница: 71 / 117

BM71

BACKHOES

D1060 & D1060UG

NOTE:

For proper

balance

and

safety,

your Magnatrac RS1000 must have a mounted #AM39

- Angle Mount Kit and either a #FW15 - Front Counterweight or a #HL295 - Hydro Loader before

you attach your Backhoe. Complete the #FW15 - Front Counterweight Instructions or #HL295 -

Hydro Loader Instructions first and then proceed to the #AM39 Angle Mount installation at this time.

Some or all of these attachments may have been factory installed for you already. Please call

if you have any questions on whether or not these attachmnets have been already installed!

Your backhoe has been fully assembled, tested at our factory and shipped on a pallet. Below

are the instructions to remove it from the pallet and attach it to your RS1000. Before proceeding,

make sure to:

Have your Pallets on a flat surface, like garage floor or flat section of your driveway.

Remove the skrink wrap and banding. Be careful as loads can shift and move quickly!

Remove any other smaller attachments that may be on the Backhoe pallet and store in a

clean dry area for later assembly.

But up the rear of the RS1000 pallet with the front of the Backhoe pallet, so the “rear of the

tractor” and “backhoe frame” are at similar heights.

If you purchased a Backhoe after your orignal purchase, you’ll need to add the correct safe

starting wires and rotating seat bracket to safely & properly operate the Backhoe. See Seat Mounting

below.

Seat Mounting

STEP 1.

Disconnect the “mating” #1824 & 1825

Seat Wires at their common “plug”. Remove #1688

Seat Pin. Remove #933A Seat & #1674 Mounting

Bracket Assembly and #1625 Arm Rests. (Photo 1).

Photo 1

1825

1625

1824

Plug

1688

1674

933A

Содержание Magnatrac RS1000






















































































































Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Бренды по названию

Популярные бренды

Struck Magnatrac RS1000, Инструкции по сборке приспособления

Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Бренды по названию

Популярные бренды