Struck Magnatrac RS1000 страница 95 Скачать руководство пользователя

Страница: 95 / 117

BM95

“fork”

142

143

Chisel

Tooth

1520

Mount

Assembly

“fork”

144

Ripper

Tooth

“fork”

STEP A.

Following Photo at right closely,

lay #143 Chisel Tooth against the two

“forks” matching the curve of the Chisel

Tooth with curve of “forks”.

STEP B.

Align two (2) holes in Chisel Tooth

with mating slot formed by the two “forks”.

Insert #BB Plow Bolt into each 1/2” hole of

Chisel Tooth and through “forks”... secure

behind with #142 Brackets and #AK Lock

Nuts... tighten.

STEP A.

Following Photo at right closely,

slip the top of the “slotted end” of the #144

Ripper Tooth between the two “forks” of the

#1520 Mount Assembly.

STEP B.

Align the 1/2” slots in Ripper Tooth

with matching 1/2” holes in “forks” of #1520

Mount Assembly.

Slip #AA Bolts into these aligned 1/2” slots

and holes and secure on reverse side with

#AK Nuts.

NOTE:

You may use the lower two 1/2”

holes to give the Ripper Tooth a different

working angle.

Chisel Tooth Installation

Ripper Tooth Installation

1520

Mount

Assembly

Lower two

1/2” holes

NOTE:

Only for use on the

D1060, D1060UG & D1065

Backhoes.

Содержание Magnatrac RS1000






















































































































Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды

Struck Magnatrac RS1000, Инструкции по сборке приспособления

Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды