Struck Magnatrac RS1000 Скачать руководство пользователя

Страница: 13 / 117

BM13

STEP 20.

Totally remove #1654

Latch Plate.

Invert it

and turn it “end to

end”. Remount it per Photo at right...

use orignal #I Bolts & #NN Nuts...

tighten... see Photo at right.

Slip 5/8” hole

end

of #1666 Lift

Linkage

off

Lower Stud... Photo at right.

STEP 21.

Load Bucket Mouth

with approximately 90 pounds of sand

bags, rocks, broken concrete, etc... set

#1665 Handle so that when you have

finished loading the Bucket Mouth that

the Bucket lies

firmly

on the floor... see

Photo below.

STEP 22.

Move

forward end

#1666 Lift Linkage so its 5/8” hole is

over

Upper Stud... secure by rotating

“upper” #1667 Arm Latch

rearward

into

locked

position... Tighten #KK Nut...

see Photo below and next page.

Lower

Stud

Lower

Stud

Upper

Stud

Nut

“rotate”

Arm Latch

1666

Lift linkage

“forward end”

1654

5/8”

hole

I Bolt &

NN Nut

Cross Shaft

“resting on” Grill

“upper” 1667 Arm Latch

“open” position”

STEP 23.

Move

forward

end

of #1666 Lift Linkage so its

5/8” hole is

over

Upper Stud...

secure by rotating “upper”

#1667 Arm Latch

rearward

into

locked

position... Tighten #KK

Nut... see Photo above and

next page.

“lower” 1667 Arm Latch

not shown

NOTE:

The MFH15 Manual Front Hitch has (2) different

height settings. For dozing applications, use the “upper

stud”. For carrying large loads use the “lower stud”. -

Contact our techs for questions on these settings.

Содержание Magnatrac RS1000






















































































































Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды

Struck Magnatrac RS1000, Инструкции по сборке приспособления

Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды