Struck Magnatrac RS1000 Скачать руководство пользователя страница 94

Страница: 94 / 117

BM94

Frost/Chisel Tooth Kit

BR50

143

1520

Mount

Assembly

000142

Bracket

(2)

000143

Chisel Tooth

(1)

000144

Ripper Tooth

(1)

001520

Mount

(1)

1/2-13x2 G5 Bolt

(2)

1/2-13x3-1/2 G5 Plow Bolt (2)

1/2-13 Spin Lock Nut

(4)

144

“forks”

STEP 1.

Drive out

the #244 Press Pins se-

curing each of the two (2) #1291 Pivot

Pins... see Photo above.

STEP 2.

Drive out the two (2) #1291 Pivot

Pins and release Bucket... Photo above.

STEP 3.

Install #1520 Mount in identical

manner as Bucket was installed... secure

in same way with #1291 Pivot Pins and

#244 Press Pins... see Photo at right.

PARTS LIST

FASTENER LIST

1520

Mount

Assembly

244

1291

Note:

#244 Pins [above]

are located against Anti-

Rotational 1/2” Washers

to resist rotating!

Anti-Rotational

1/2” Washers

142

Содержание Magnatrac RS1000






















































































































Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Бренды по названию

Популярные бренды

Struck Magnatrac RS1000, Инструкции по сборке приспособления

Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Бренды по названию

Популярные бренды