Struck Magnatrac RS1000 Скачать руководство пользователя

Страница: 43 / 117

BM43

Dozer Blade Assembly “face down”

Dozer Blade Assembly - “face down”

4120

Bottom

Blade

Mount

STEP 2.

Turn #4103 Box Scraper Assembly “face down”. Lower Dozer Blade Assem-

bly “face down”

into

the Box Scraper Assembly... align five (5) 3/8”

slots

in “lower edge” of

Box Scraper Assembly with mating five (5) 3/8”

holes

in “lower edge” of Dozer Blade Assem-

bly. From

front face

of Blade, insert orignal five (5) #R Bolts into aligned holes & slots.

STEP 3.

Replace #4120 Bottom Blade Mount by sliping its three (3) 3/8” holes

onto the three (3) protruding Bolts in

center

of Dozer Blade Assembly... Secure all five (5)

#R Bolts in lower edge of Blade Assembly with #HH Nuts... finger tight... see Photo above.

STEP 4.

Align 3/8” holes in

top right

left

corners of Dozer Blade Assembly with

mating 3/8” slots in

top right

left

corners of Box Scraper Assembly. Insert #R Bolts into

aligned 3/8” holes & slots and secure with #NN Nuts. Tighten all seven (7) #HH Nuts in-

stalled in this “assembly”... see Photo next page.

4013 Box Scraper Assembly “face down”

Dozer Blade Assembly - “face down”

R Bolts & NN Nuts

Содержание Magnatrac RS1000






















































































































Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды

Struck Magnatrac RS1000, Инструкции по сборке приспособления

Результаты поиска

Содержание Magnatrac RS1000

Отзывы:

Похожие инструкции для Magnatrac RS1000

Бренды по названию

Популярные бренды